iPhone 4 TEARDOWN + VIDEO

[ddub420]

Tech Specs: Apple - iPhone 4 - Size, weight, battery life, and other specs

iPhone 4 Teardown by ifixit.com

Interestingly enough, the storage capacity is not etched on the outer case of the iPhone 4.
We'd expect our 32 GB iPhone 4 to fulfill its promise and give us, well, 32 GB. Unfortunately it has an actual capacity of 29.06 GB.
Given the fact that 301 MB of "other" data is being stored in memory, this leaves the user with 28.77 GB of free space.
In terms of OS, the iPhone 4 comes preinstalled with the newly released iPhone OS 4, build 8A293.
The iPhone 4 is Model A1332. Interestingly, that's a lower number than the A1337 iPad 3G.

Like the iPhone 3G and 3GS, there are two silver Phillips #00 screws at the bottom of the phone.
In a departure from the design of the 3G and 3GS, removing the screws releases the rear case, not the front glass.
This design makes switching out the rear panel trivial, but unfortunately means that replacing the iPhone 4 front panel will likely be rather challenging.

Removing rear panel gives us a pretty good look at the iPhone 4's innards.
Holy battery! The inside of this thing is dominated by its juice-provider.
It's pretty apparent that real estate was very limited inside the iPhone 4's 115.2 x 58.6 x 9.3 mm footprint.
You can also see the antenna's pressure contact on the inner face of the rear panel.

Luckily, the battery can be easily removed once the back panel assembly is out of the way.
The 3.7V 1420 mAh Li-Polymer battery allows for up to 7 hours of talk time on 3G or up to 14 hours on 2G.
The battery connector is different than the one in the 3G and 3GS. Fortunately, the battery is not soldered to the logic board. This will make battery replacement on the iPhone 4 fairly easy to accomplish.
The plastic pull tab for the battery says "Authorized Service Provider Only."

No EMI shield will stand between us and the innards of this iPhone 4!
The EMI shield comes off after four screws are removed to reveal lots of important connectors.

The logic board is heavily embedded under wires and EMI shields.
While we're not too busy, let's talk RAM. Unlike the iPhone 3GS and iPad, which are both equipped with 256 MB, the iPhone 4 has a whopping 512 MB!
The increase in RAM allows for a larger amount of cached data allowing for a smoother and faster user experience.

Hiding in the corner is the iPhone 4's vibrator motor, which...well...vibrates.

Removing one of the many connectors on the logic board.
In our brief usage, we did notice that the phone is considerably warmer on the right side. This makes sense, as the logic board is located entirely along the right side of the phone.

Behold a beauty in the iPhone 4: a rear-facing 5 MP camera with 720p video at 30 FPS, tap to focus feature, and LED flash.
This is a huge upgrade from the 3.2 MP camera found in the iPhone 3GS.

Removing the lower antenna/speaker enclosure from the bottom of the phone.
The improved audio chamber aids in clarifying sounds leaving the iPhone, including calls via speakerphone as well as music played through the speaker inside this housing.
Apple hasn't made taking the iPhone 4 apart very hard so far: no 5-point Torx bits or fragile clips to be seen.

Removing the logic board.
The unusual shape and small size of the logic board shows just how costly real estate is inside this powerhouse of a phone.

In what can only be described as a work of genius, Apple has integrated the UMTS, GSM, GPS, Wi-Fi, and Bluetooth antennas into the stainless steel inner frame.
The dual purpose stainless steel inner frame/antenna assembly addresses possibly the two biggest flaws concerning previous iterations of the iPhone: continuous dropped calls and lack of reception.
Apple has gone a step further and tuned the phone to utilize whichever network band is less congested or has the least interference for the best signal quality, regardless of the actual signal strength. Early reports suggest this feature, while buggy in its early stages, will greatly improve the phone's reliability on AT&T's fragile network.

With the EMI shields off, we can get a look at what makes this beast roar.
Lurking deep within the phone, the A4 processor, manufactured by Samsung, is the centralized unit that provides the iPhone 4 with the much needed computing power.
Replacing the Samsung S5PC100 ARM A8 600 MHz CPU used in the 3GS, the new iPhone uses the 1 GHz ARM Cortex A8 core, much like its bigger sibling, the iPad.
The new Samsung Wave S8500 smartphone uses the same Cortex A8 core!
Just to the left of the A4 package, the AGD1 is the new 3 axis gyroscope that we believe is designed and manufactured by ST Micro for Apple. The package marks on this device do not appear to be the currently available commercial part, L3G4200D. The commercial version of this gyroscope is yet to be released — Apple got first dibs on it.

On the top of logic board:

Skyworks SKY77542 Tx–Rx iPAC™ FEM for Dual-Band GSM/GPRS: 880–915 MHz and 1710–1785 MHz bands.
Skyworks SKY77541 GSM/GRPS Front End Module
STMicro STM33DH 3-axis accelerometer
TriQuint TQM676091

On the back:

Samsung K9PFG08 flash memory
Cirrus Logic 338S0589 audio codec (Apple branded). This is the same part as in the iPad.
AKM8975 - newest magnetic sensor that promises to improve the performance over the prior generation.
Texas Instruments 343S0499 Touch Screen Controller
36MY1EE Numonyx NOR and mobile DDR

Wi-Fi, Bluetooth, and GPS are all provided by Broadcom and located beneath EMI shields on the front side of the board.
Broadcom BCM4329FKUBG 802.11n with Bluetooth 2.1 + EDR and FM receiver.
Broadcom BCM4750IUB8 single-chip GPS receiver.

Up next we find the second microphone, which is used to cut out ambient noise and improve sound quality when talking on the phone.

The front-facing VGA camera.
While the 5 megapixel camera on the rear of the iPhone 4 is ideal for video recording, the smaller camera on the front optimizes use of Apple's FaceTime for mobile-to-mobile video calls.

The front panel comes off without too much additional trouble.
The stainless steel body left behind is quite a marvel of gadget engineering.

The front glass panel of the iPhone is constructed of Corning Gorilla Glass, a chemically strengthened alkali-aluminosilicate thin sheet glass that is reported to be 20 times stiffer and 30 times harder than plastic.
Gorilla Glass holds many advantages as the iPhone 4's front panel, including its high resistance to wear and increased strength from an ion-exchange chemical strengthening process.
LED Backlight for the LCD.
Unfortunately, the LCD panel is very securely glued to the glass and digitizer. It appears that if you break the glass, you'll have to replace the iPhone 4's glass, digitizer, and LCD as a single assembly.

Surprisingly, the electronic home button switch is attached directly to the home button itself.

The 30-pin dock connector is where we would usually expect it to be: at the bottom of the iPhone.
The primary microphone is also found at the bottom of the phone.

Apple is following in the footsteps of the Nexus One by using dual microphones to help improve audio quality and suppress background noise.
Interestingly, the two microphones are positioned at the two far ends of the phone. The microphone at the top of the iPhone is most likely utilized for capturing background noise to be analyzed by internal circuitry and used to cancel any noise put into the main microphone other than the user's voice.

As always, we provide each device with a fitting final layout shot that it so greatly deserves.

TEARDOWN by iFixit: The free repair manual

EDIT:

VIDEO TEARDOWN by tech restore

http://www.youtube.com/watch?v=YkcLLI6Yv8I

Take a look at this stop-motion teardown video of the iPhone 4 made by TechRestore using 1784 high resolution photographs.

[Superman]

Good work

[Akii]

Nice!

[Mr.x]

wow thats awesome.

[ddub420]

iPhone 4G antenna

[soul]

HOT

[tiggerlator]

Thanks very interesting.

[djmajor1980]

Hey there!
Thanks for the awsome work!

Just one question:

It says:

".......Wi-Fi, Bluetooth, and GPS are all provided by Broadcom and located beneath EMI shields on the front side of the board.
Broadcom BCM4329FKUBG 802.11n with Bluetooth 2.1 + EDR and FM receiver.
Broadcom BCM4750IUB8 single-chip GPS receiver......."


Does this mean, that it is possible to listen to normal radio stations via UKW, FM and such (not the internet radio streamed via wlan or 3g)


Please let me know!
I am interested because I am on a 200MB Data plan at T-Mobile! Listing to internetradio does use up a lot of data-Traffic!!


THANKS!!!

[Exd3ath]

cool pics. Very interesting on how it's put together.

[ddub420]

Some more interesting images........

[cane_2042]

Thanks for the info

[karma]

it's iPhone 4 not iPhone 4G

Not sure why everyone seems to be making this typo...

[ddub420]

Originally Posted by karma_

it's iPhone 4 not iPhone 4G

Not sure why everyone seems to be making this typo...

I put the G in there for Fourth Generation.

[karma]

but that's already implied with the "4"

I'm just nitpicking cuz I'm bored, sorry lol

[ddub420]

it probably will confuse some people if i leave it like that....title changed.

And for those who found this interesting check out the iphone 4 gyroscope teardown
iPhone 4 Gyroscope Teardown - SiNfuL iPhone

[ddub420]

http://www.youtube.com/watch?v=YkcLLI6Yv8I

Take a look at this stop-motion teardown video of the iPhone 4 made by TechRestore using 1784 high resolution photographs.

very cool

**added to OP**

[Mr.x]

That was truely amazing

[ddub420]

Originally Posted by Mr.x

That was truely amazing

I agree, I've watched that vid @ least 8 times today.
Very well put together, especially the part near the end.

[-shadow-]

thats great thanks. very interesting also

[andymp3]

Wow...They are quite the piece of engineering. I work for Rogers and tomorrow is the Canadian release date...It will be a busy day for me.....They are priced right as well...Should be a good day...lol